Cmc Marine Pl-65 Transom Jack Plates By T-H Marine

Priced: $299.99 Rated:   - 5 stars out of 5 by 4 reviews.
Visit our Daily Deals for great products at low prices.
Cmc Marine Pl-65 Transom Jack Plates By T-H Marine -
CMC PL-65 Transom Jack Plate is a unique outboard motor hydraulic lifting device that works independently of your power trim and tilt to allow you to adjust your motor down while underway for better out-of-hole shots or up for more top-end speed and more prop clearance in shallow water. Made of tough, 1/2" aluminum alloy with stainless steel fasteners. These units are designed to fit all standard outboards and provide a 5-1/2" setback and 5" of vertical travel. Position-indicator gauge mounts in dash of boat for easy and safe determination of motor height. Sending unit is completely sealed and waterproof.
Maximum lift: 5".
CMC Manual Transom Jack is the same size and has the same features as the above model, but with a manual lift jack. Threaded shaft for easy height adjustment with wrench. Top 25 Category Product
View other top products in this category...
Want it cheaper? Set your own price.
Enter the price you want to pay and we'll email or text you if we find a store that will sell it for that amount:
Price: $
Your email:
Cell number: (optional, for text message)
Learn how offers work...
Average Price History: Price History
Review RatingNumber of Reviews

Cmc Marine Pl-65 Transom Jack Plates By T-H Marine Reviews:


works well could use a couple improvements

I converted my 115 Yamaha 2 stroke from a jet pump to prop and needed to change the transom height. This was a great solution so I can reinstall and use the jet in the future. Installation was pretty straight forward and it seems to work very well once installed. However I'd like to see some changes. 1- better quality actuator power cord - the outer plastic insulation is very stiff in cooler weather say 30- 45 degrees F. Living in remote Alaska we may work down into the 20s even colder and I'm concerned the cord to the actuator unit might break. 2-The plastic connector DID break in high 30's as I was installing and I had to replace it - which may nullify the warranty - boo. Also the wires were reversed in this connector so no matter what I did to the control switch Up was Down and Down was Up until I replaced the connector. 3-Updating the instruction sheet with some color photos might make them a little easier to follow. 4- please include fluid recommendations for cold weather operations. The customer help online was VERY FAST and helpful but it would be nice to have it on the printed sheets. In my chilly weather the supplied fluid was pretty slow. Haven't done the replacement yet - too cold now will have to wait for spring. I'm wondering how quickly this will work in warmer weather; its not a hight speed lift in 30s. 5- kudos for marking the wires to the control switch - very helpful. 6- this is a very sturdy unit and inspires confidence. 7- a friend has one [10 inch] holding his 90 hp 4 stroke Yamaha and loves it. Overall - a real answer to my needs and I didn't have to have my transom cut and rewelded.
Nerka at Cabelas on 10/30/2012

CMC PL-65 Jack Plate forJet Boat

I recently converted my 90hp Merc to a Jet on my 17 foot starcraft. The transom jack works exactly as it should in this application. Solidly built and the holes lined up perfectly for the motor. Only thing I wish is that it had another inch or two of travel so I could cut down on the transom spray from the jet. No problems with cavitation/air ingestion due to the set back of the plate which some people had told me could be a possibility. Easy to put on, had the motor mounted and the jet pump converted in a few hours. I am very pleased with this product.
JetSledSteve at Cabelas on 08/03/2009

CMC manual jack plate

Purchased the manual jack plate for my 16' fiberglass bass boat. Boat would porpoise when trimmed up, even with a hydrofoil. Installed the jack plate, and porpoising was eliminated and I no longer need the hydrofoil. Boat gained about 2-3 mph also. Couldn't be happier. Jack plate is well built and easy to adjust. Predrilled holes lined up perfectly to my 100 hp 4 cylinder.
lv2fishmn at Cabelas on 05/05/2011

best thing on my boat

if you want a jackplate get this one!i love it.i put it on my 70hp johnson on a 19ft boat eveything fit great .
duxmasher99999 at Cabelas on 09/28/2012